Page 1
Passage 2 The Development of Plastics
1
SECTION 2
READING PASSAGE 2
You should spend about 20 minutes on Question 14-26 which are based on Reading
Passage 2 below.
The Development of Plastics
A
When rubber was first commercially produced in Europe during the nineteenth century,
it rapidly became a very important commodity, particularly in the fields of
transportation and electricity. However, during the twentieth century a number of new
synthetic materials, called plastics, superseded natural rubber in all but a few
applications.
B
Rubber is a polymer – a compound containing large molecules that are formed by the
bonding of many smaller, simpler units, repeated over and over again. The same
bonding principle – polymerisation – underlies the creation of a huge range of plastics
by the chemical industry.
C
The first plastic was developed as a result of a competition in the USA. In the 1860s,
$10,000 was offered to anybody who could replace ivory – supplies of which were
declining – with something equally good as a material for making billiard balls. The prize
was won by John Wesley Hyatt with a material called celluloid. Celluloid was made by
dissolving cellulose, a carbohydrate derived from plants, in a solution of camphor
dissolved in ethanol. This new material rapidly found uses in the manufacture of
products such as knife handles, detachable collars and cuffs, spectacle frames and
photographic film. Without celluloid, the film industry could never have got off the
ground at the end of the 19th century.
D
Celluloid can be repeatedly softened and reshaped by heat, and is known as a
thermoplastic. In 1907 Leo Baekeland, a Belgian chemist working in the USA, invented a
different kind of plastic by causing phenol and formaldehyde to react together.
Baekeland called the material Bakelite, and it was the first of the thermosets – plastics
that can be cast and moulded while hot, but cannot be softened by heat and reshaped
Page 2
Passage 2 The Development of Plastics
2
once they have set. Bakelite was a good insulator, and was resistant to water, acids and
moderate heat. With these properties it was soon being used in the manufacture of
switches, household items, such as knife handles, and electrical components for cars.
E
Soon chemists began looking for other small molecules that could be strung together to
make polymers. In the 1930s, British chemists discovered that the gas ethylene would
polymerise under heat and pressure to form a thermoplastic they called polythene.
Polypropylene followed in the 1950s. both were used to make bottles, pipes and plastic
bags. A small change in the starting material – replacing a hydrogen atom in ethylene
with a chlorine atom – produced PVC (polyvinyl chloride), a hard, fireproof plastic
suitable for drains and gutters. And by adding certain chemicals, a soft form of PVC
could be produced, suitable as a substitute for rubber in items such as waterproof
clothing. A closely related plastic was Teflon, as PTFE (polytetrafluoroethylene). This had
a very low coefficient of friction, making it ideal for bearings, rollers, and non-stick frying
pans. Polystyrene, developed during the 1930s in Germany, was a clear, glass-like
material, used in food containers, domestic appliances and toys. Expanded polystyrene
– a white, rigid foam – was widely used in packaging and insulation. Polyurethanes, also
developed in Germany, found uses as adhesives, coatings, and – in the form of rigid
foams – as insulation materials. They are all produced from chemicals derived from
crude oil, which contains exactly the same elements – carbon and hydrogen – as many
plastics.
F
The first of the man-made fibres, nylon, was also created in the 1930s. Its inventor was a
chemist called Wallace Carothers, who worked for the Du Pont company in the USA. He
found that under the right conditions, two chemicals – hexamethylenediamine and
adipic acid --- would form a polymer that could be pumped out through holes and then
stretched to form long glossy threads that could be woven like silk. Its first use was to
make parachutes for the US armed forces in World War II. In the post-war years nylon
completely replaced silk in the manufacture of stockings. Subsequently many other
synthetic fibres joined nylon, including Orion, Acrilan and Terylene. Today most
garments are made of a blend of natural fibres, such as cotton and wool, and man-made
fibres that make fabrics easier to look after.
G
The great strength of plastic is its indestructibility. However, this quality is also
something of a drawback: beaches all over the world, even on the remotest islands, are
Page 3
Passage 2 The Development of Plastics
3
littered with plastic bottles that nothing can destroy. Nor is it very easy to recycle
plastics, as different types of plastic are often used in the same items and call for
different treatments. Plastics can be made biodegradable by incorporating into their
structure a material such as starch, which is attacked by bacteria and causes the plastic
to fall apart. Other materials can be incorporated that gradually decay in sunlight –
although bottles made of such materials have to be stored in the dark, to ensure that
they do not disintegrate before they have been used.
Questions 14-20
Complete the table below
Choose NO MORE THAN THREE WORDS from the passage for each answer.
Write your answers in boxes 14-20 on your answer sheet.
Name of
plastic
Date of
invention
Original
region
Property Common
use
Celluloid 1860s US Clothing and
14……………….
15………………. 1907 US can be cast
and moulded
but cannot be
softened by
heat
16………………,
household
items and
car parts
Polythene 1930s 17………… Bottles
Rigid PVC 18………………… drains and
gutters
Polystyrene 1930s Germany transparent
and
resembled to
19………………..
Food
container
domestic
Polyurethanes Germany Formation
like
20…………………
adhesives,
coatings and
insulation
Page 4
Passage 2 The Development of Plastics
4
Questions 21-26
Do the following statements agree with the information given in Reading Passage 2?
In boxes 21-26 on your answer sheet, write
YES if the statement is true
NO if the statement is false
NOT GIVEN if the information is not given in the passage
21 The chemical structure of plastic is very different from that of rubber.
22 John Wesley was a famous chemist.
23 Celluloid and Bakelite react to heat in the same way.
24 The mix of different varieties of plastic can make them less recyclable.
25 Adding starch into plastic does not necessarily make plastic more durable.
26 Some plastic containers have to be preserved in special conditions.
Page 5
Passage 2 The Development of Plastics
5
ANSWER
14. Photographic film
15. Bakelite
16. (electric) switches
17. Britain/UK
18. fireproof
19. glass
20. rigid foams
21. FALSE
22. NOT GIVEN
23. FALSE
24. TRUE
25. TRUE
26. TRUE
Showing the first 5 pages. Download the document to see it all.
Comments (0)
No comments yet. Be the first!